*其他論文*

第一頁 第二頁 第三頁 第四頁 第五頁 第六頁 第七頁 第八頁 第九頁 第十頁 第11頁

⊙第51篇⊙

**Study
on Hydrothermal Cracking of Heavy Oils: Formation of Radical Under Lower Reaction
Temperature**

（下載英語論文全文請點擊上面的鏈接）

注意：本論文已在Anal.
Rep. Eng. Res. Inst. Facul. Eng. Univ. Tokyo, vol.59, pp.111發表

使用者請注明論文出處

Jie CHANG（常杰）, Noritatsu TSUBAKI and Kaoru FUJIMOTO

SYNOPSIS

The hydrothermal cracking of heavy
oils, Canadian oil sand bitumen and Arabian heavy vacuum resid, as well as
their model compound were performed over Ni/Al2O3 and NiMo/Al2O3 catalysts
under 663-703 K and 5.0 MPa of hydrogen pressure in a autoclave reactor. The
conversions of heavy oils and their model compound were remarkably enhanced
by adding some free radical initiators, such as peroxide and sulfur. The reaction
mechanism on model compound, 1-phenyldodecane (PhDD), suggested that the hydrogen
in hydrocarbon was easily abstracted by free radicals that were formed from
initiators under lower temperature, and the chain reactions were readily initiated.
Therefore, the conversion was obviously increased even at lower reaction temperature.

⊙第52篇⊙

**Hydrothermal
cracking of Residual Oil**

（下載英文論文全文請點擊上面的鏈接）

注意：本論文已在Acta Petrolei
Sinica (Petroleum Processing Section), Vol.17 (1), pp.42發表

使用者請注明論文出處

Kaoru Fujimoto, Jie Chang（常杰） and Li Fan

Department of Applied Chemistry, School of Engineering, The University of
Tokyo,

Hongo 7-3-1, Bunkyo-ku, Tokyo, 113-8656, Japan

**Abstract:**Hydrothermal
cracking process of residual oil has been developed by our group for many
years to upgrade heavy oil feedstock into valuable middle distillate products.
It is a tailor-made combined process of thermal cracking and catalytic hydrogenation.
This process can suppress gas and toluene insoluble coke yields and promote
middle distillate yield comparing with thermal cracking process at the same
conversion level. Hydrothermal cracking process was operated at high reaction
temperature (693~733 K) and medium hydrogen partial pressure (3.0~8.0 MPa).
Experiments were conducted in batch autoclave reactors and semi-batch reaction
systems respectively. Series of catalysts were prepared from different supports
(MgO, active carbon, SiO2 and Al2O3) and active metals ( Ni, Mo, Co and W,
etc.). Feedstock such as bitumen, AR (atmospheric resid) and VR (vacuum resid)
were tested. The structure of feedstock and products were characterized by
1H-NMR. The reuse ability and regeneration of catalysts were studied as well.
Alumina-supported catalysts showed better performance and regeneration ability.
The reaction mechanism of hydrothermal cracking was also studied by model
compound and proposed as one consisting of thermal cracking of hydrocarbon
molecules via free radical chain reactions and catalytic quench of free radicals
by hydrogen.

⊙第53篇⊙

**Free-surface
waves and far wakes generated by a floating body in a viscous fluid. Journal
of Hydrodynamics**

（下載英語論文全文請點擊上面的鏈接）

注意：本論文已在.
Journal of Hydrodynamics, Ser. B, Vol. 15, No. 4, pp.10-16. Aug. 2003.發表

使用者請注明論文出處

Lu Dong-qiang.(盧東強)

Department of Mechanical Engineering, The University of Hong Kong, Hong Kong,
China

Shanghai institute of Applied Mathematics and Mechanics, Shanghai University,
Shagnhai, 200072, China

**Abstract: **The free-surface
waves and the flow field due to a body moving on the surface of an incompressible
viscous fluid of infinite depth were studied analytically. The floating body
was modeled as a normal point pressure on the free surface. Based on the Oseen
approximation for governing equations and the linearity assumption for boundary
conditions, the exact solutions in integral form for the free-surface elevation,
the velocities and the pressure were given. By employing Lighthill's two-stage
scheme, the asymptotic representations in far field for large Reynolds numbers
were derived explicitly. The effect of viscosity on the wave profiles was
expressed by an exponential decay factor, which removes the singular behavior
predicted by the potential theory.

**Keywords:** free-surface waves, velocity distribution, floating body,
viscosity, asymptotic representation, Lighthill's two-stage scheme

⊙第54篇⊙

**非線性水波Hamilton系統理論與應用研究進展**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《力學進展》
28卷4期,521-531頁,
1998年11月發表

使用者請注明論文出處

張寶善, 盧東強,
戴世強, 程友良

（上海大學，上海市應用數學和力學研究所，上海，200072）

**摘要：** 概述了辛幾何理論與辛算法在Hamilton力學中的應用，綜述非線性水波的Hamilton理論研究進展。闡述非線性水波Hamilton變分原理與方法的優越性與局限性，探討KdV方程和BBM方程的Hamilton描述、對稱性與守恒律。提出非線性水波Hamilton描述研究中有待進一步研究的問題和解法設想。

**關鍵詞：** Hamilton變分原理，辛幾何，非線性水波，Hamilton系統，對稱性與守恒律

**Research progress
on theories and applications of Hamiltonian system in nonlinear water waves **

Zhang Baoshan, Lu Dongqiang,
Dai Shiqiang, Cheng Youliang

(Shanghai Institute of Applied Mathematics & Mechanics, Shanghai University,
Shanghai, China, 200072)

**Abstract: **This paper is
a summary of the applications of symplectic theories algorithms to Hamiltonian
mechanics and the research progress Hamiltonian formulation for nonlinear
water waves. The advantages and limitations of Hamiltonian variational principle
and approaches for nonlinear water waves are discussed. In addition, it includes
also discussions on the Hamiltonian formalism, symmetry and conservation laws
of KdV equation and BBM equation and comments on the problems concerned.

**Keywords: **Hamiltonian principle, symplectic geometry, nonlinear water
waves, Hamiltonian systems, symmetry and conservation laws.

⊙第55篇⊙

**新型Poisson
括號意義下的無窮維Lie代數**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《力學學報》
1998年30卷3期,307-313頁,
1998年5月發表

使用者請注明論文出處

張寶善, 盧東強,
戴世強

（上海大學，上海市應用數學和力學研究所，上海，200072）

**摘要：** 本文首先針對DdV方程的Hamilton形式，建立一種比較容易驗證的新型Poisson括號和無窮維Lie代數。其次，研究KdV方程的Hamilton形式的第一積分與新型Poisson括號的關系，得到判定第一積分的充分必要條件。最后，構造KdV方程的第一積分。

**關鍵詞：** KdV方程，Hamilton形式，第一積分，Poisson括號，無窮維Lie代數

**Infinite-Dimensional Lie Algebra
With a New Poisson Bracket **

Zhang Baoshan, Lu Dongqiang,
Dai Shiqiang

(Shanghai Institute of Applied Mathematics & Mechanics, Shanghai University,
Shanghai, China, 200072)

**Abstract: **For the
Hamiltonian formulation of the Korteweg-de Vires equation (KdV equation),
C.S. Gardner defined a Poisson bracket. In this paper a brand-new bracket
is defined. It is easily verified that new bracket possesses three properties
of the Poisson bracket, bilinearity, skew symmetry, Jacobi identity. The new
Poisson bracket has a close connection with C.S. Gardner's definition. In
the framework of the new Poisson bracket, all the first integrals of the KdV
equation constitute an infinite-dimensional Lie algebra. Then the necessary
and sufficient conditions for identifying the first integrals are obtained.
Finally, the method for finding first integrals of KdV equation is investigated.

**Keywords: **KdV equation, Hamiltonian formulation, first integral, Poisson
bracket, infinite-dimensional, Lie algebra..

⊙第56篇⊙

**計算機輔助創新概念設計方法研究**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《Proceedings
of the 5th International Conference on Frontiers of Design and Manufacturing
(ICFDM'2002)》發表

使用者請注明論文出處

(ISTP收錄本文)

賴朝安 孫延明 黃平 鄭時雄

（華南理工大學 機械工程學院 廣州 510640）

**摘 要：** 依據多級菱形思維模型，分析基于實例的推理、遺傳算法的不足并指出其深層原因是不符合多級菱形思維模型。提出引入聚類分析方法，用實例檢索、聚類分析與遺傳算法優化模擬多級菱形思維過程。通過減少從用戶需求到產品結構的映射次數以保證第一次收斂的效果，定義產品結構相似性并推導出相似度計算公式以實現聚類分析，并依此改進實例檢索效果與遺傳算法性能來促進創新設計。

**關鍵詞：**創新設計；基于實例的推理（CBR）；聚類分析（CA）；遺傳算法（GA）

中圖分類號：TH122 文獻標識碼：A

**RESEARCH ON COMPUTER–AIDED
CREATIVE CONCEPTUAL DESIGN METHOD **

LAI Chaoan, SUN Yanming,
HUANG Ping, ZHENG Shixiong

Institute of Mechanical Engineering, South China University of Technology,
Post Code 510640

**ABSTRACT:**According to the
model of multilevel rhombus thought (MRT), the drawbacks in CBR and GA were
analyzed and it was pointed out that the fundamental reason to their drawbacks
was their deviating from the model of MRT. Cluster analysis method was applied
with a view to bind CBR, cluster analysis and GA together to simulate a MRT
process. It was pointed out that mapping times from customer needs to physical
structure should be reduced in order to guarantee the effect of first convergence.
The definition of similarity and the arithmetic formula of similarity measure
for physical structure were put forth in order to carry out cluster analysis.
Above method improves the effect of case retrieval and the performance of
GA and aid in the design of creative artifacts.

**Keywords: ** Creative designing; Case-Based Reasoning (CBR); Cluster
analysis; Genetic Algorithms (GA)

⊙第57篇⊙

**Multiple
travelling wave solutions of nonlinear evolution equations using a unified
algebraic method**

（下載英語論文全文請點擊上面的鏈接）

注意：本論文已在《
JOURNAL OF PHYSICS A: MATHEMATICAL AND GENERAL 35 (2002) 6853–6872 》發表

使用者請注明論文出處

(SCI收錄本文)

Engui Fan（范恩貴）

Institute of Mathematics, Key Laboratory for Nonlinear Mathematical Models
and Methods,

Fudan University, Shanghai 200433, People’s Republic of China

**Abstract：**A
new direct and unified algebraic method for constructing multiple travelling
wave solutions of general nonlinear evolution
equations is presented and implemented
in a computer algebraic system. Compared with most of the existing
tanhmethods, the Jacobi elliptic functionmethod or other sophisticated
methods, the proposed method not only gives new
and more general solutions, but also provides
a guideline to classify the various types of the travelling wave
solutions according to the values of some parameters. The solutions
obtained in this paper include (a) kink-shaped
and bell-shaped soliton solutions, (b)
rational solutions, (c) triangular periodic solutions and (d) Jacobi and
Weierstrass doubly periodic wave solutions. Among
them, the Jacobi elliptic periodic wave
solutions exactly degenerate to the soliton solutions at a certain
limit condition. The efficiency of the method
can be demonstrated on a large variety
of nonlinear evolution equations such as those considered in this
paper, KdV–MKdV, Ito’s fifth MKdV, Hirota, Nizhnik–Novikov–Veselov,
Broer–Kaup, generalized coupledHirota–Satsuma,
coupled Schr¨odinger–KdV, (2 + 1)-dimensional
dispersive long wave, (2 + 1)-dimensional Davey– Stewartson
equations. In addition, as an illustrative sample, the properties of
the soliton solutions and Jacobi doubly periodic solutions for the Hirota
equation are shown by some figures. The links
among our proposed method, the tanh method,
extended tanh method and the Jacobi elliptic function method are
clarified generally.

⊙第58篇⊙

**A
family of completely integrable multi-Hamiltonian systems explicitly related
to some celebrated equations**

（下載英文論文全文請點擊上面的鏈接）

注意：本論文已在《JOURNAL
OF MATHEMATICAL PHYSICS VOLUME 42, NUMBER 9 SEPTEMBER 2001:4327-4344》發表

使用者請注明論文出處

(SCI收錄本文)

Engui Fan（范恩貴）

Institute of Mathematics, Fudan University, Shanghai 200433, People’s Republic
of China

~Received 2 October 2000; accepted for publication 4 June 2001

By introducing a spectral problem with an arbitrary parameter, we derive a Kaup–Newell-type hierarchy of nonlinear evolution equations, which is explicitly related to many important equations such as the Kundu equation, the Kaup–Newell ~KN! equation, the Chen–Lee–Liu ~CLL! equation, the Gerdjikov–Ivanov ~GI! equation,the Burgers equation, the modified Korteweg-deVries ~MKdV! equation and the Sharma–Tasso–Olver equation. It is shown that the hierarchy is integrable in Liouville’s sense and possesses multi-Hamiltonian structure. Under the Bargann constraint between the potentials and the eigenfunctions, the spectral problem is nonlinearized as a finite-dimensional completely integrable Hamiltonian system. The involutive representation of the solutions for the Kaup–Newell-type hierarchy is also presented. In addition, an N-fold Darboux transformation of the Kundu equation is constructed with the help of its Lax pairs and a reduction technique. According to the Darboux transformation, the solutions of the Kundu equation is reduced to solving a linear algebraic system and two first-order ordinary differential equations. It is found that the KN, CLL, and GI equations can be described by a Kundu-type derivative nonlinear Schro¨dinger equation involving a parameter. And then, we can construct the Hamiltonian formulations, Lax pairs and N-fold Darboux transformations for the Kundu, KN, CLL, and GI equations in explicit and unified ways.

⊙第59篇⊙

**三維邊坡穩定性極限平衡分析系統軟件SLOPE^3D的設計及應用**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《巖石力學與工程學報.2003,22(7):1121-1125
》發表

使用者請注明論文出處

姜清輝 ,2 王笑海2 豐定祥2 馮樹仁2

（1.武漢大學水力發電工程系 武漢430072；2.中國科學院武漢巖土力學研究所 武漢 430071）

**摘要: ** 為了拓展三維極限平衡法在實際工程中的廣泛應用，邊坡穩定性分析可視化系統軟件3D_SLOPE被研制和發展。它由前處理、極限平衡分析求解器和后處理組成，前處理核心是構造三維邊坡地質模型，后處理主要是計算結果分析和可視化圖形顯示。該系統將邊坡工程地質信息三維可視化技術和穩定性分析有機地結合起來，由于其良好的用戶界面和高質量的三維圖形顯示能力，人們能夠容易地將其應用到實際邊坡工程問題。

**關鍵詞: ** 邊坡穩定性分析 ，極限平衡法 ，三維可視化

**Three Dimensional Limit Equilibrium Analysis System Software
3D_SLOPE
for Slope Stability and its Application**

Jiang Qinghui1 Wang Xiaohai2 Feng Dingxiang2 Feng Shuren2

(1College of Water Conservancy and Hydropower Engineering, Wuhan University,430072,China)

(2 Institute of Rock and Soil Mechanics, The Chinese Academy of Sciences,
Wuhan 430071)

**Abstract ** In order to pursue three-dimensional limit
equilibrium analysis methods to widely practical applications, an interactive
visualization system software 3D_SLOPE for slope stability analysis has been
developed. It contains the pre-processor, the limit equilibrium analysis solver
and the post-processor. In the pre-processor, the construction of three-dimensional
geological model of the slope structure provides geoinformation presentation
for the limit equilibrium solver. In the post-processor, the effective three-dimensional
visualization of data sets can assist the user with interpretation and analysis
of the calculation results. The 3D_SLOPE system combined 3-D visualization
of geoinformation in slope engineering with limit equilibrium analysis for
slope stability. Because of its user-friendly interface and high-quality 3-D
graphics capabilities, the geotechnical engineers can easily apply 3D_SLOPE
to practical engineering problems.

**Key Words ** analysis of slope stability, limit equilibrium method, three-dimensional
visualization

⊙第60篇⊙

**A
Model of Point-to-Face Contact for Three-Dimensional Discontinuous Deformation
Analysis**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《Rock
Mechanics and Rock Engineering. August 18, 2003 # Springer-Verlag》發表

使用者請注明論文出處

Q. H. Jiang1（姜清輝） and M. R. Yeung2

1State Key Laboratory of Water Resources and Hydropower Engineering Science

Wuhan University, Wuhan, P.R. China

2Department of Civil Engineering, The University of Hong Kong, Hong Kong,
P.R. China

Received August 30, 2002; accepted April 7, 2003

**Summary:**The key to three-dimensional discontinuous deformation
analysis (3D DDA) is a rigorous contact theory that governs the interaction
of many three-dimensional blocks. This theory must provide algorithms to judge
contact types and locations and the appropriate state of each contact, which
can be open, sliding or locked. This paper presents a point-to-face contact
model, which forms a part of the contact theory, to be used in 3D DDA. Normal
spring, shear spring and frictional force submatrices are derived by vector
analysis and the penalty method. Also given are the ‘‘openclose’’ iteration
criteria and operations performed for different changes in contact state.
Sliding at a contact can occur in any direction parallel to the contact face,
as opposed to one of two directions in two-dimensional DDA. This point-to-face
contact model has been implemented into a 3D DDA computer program, and numerical
results from several test cases demonstrate the validity of the model and
the capability of the program.

**Keywords: ** 3D DDA, point-to-face contact, open-close iteration.

⊙第61篇⊙

**Dosing
system for the nanolitre range,fabricated with the AMANDA process**

（下載英語論文全文請點擊上面的鏈接）

注意：本論文已在《JOURNAL OF MICROMECHANICS
AND MICROENGINEERING. 13 (2003) S85–S90》發表

使用者請注明論文出處

P Shao(邵培革), Z Rummler and WK Schomburg

Forschungszentrum Karlsruhe, Institut f¨ur Mikrostrukturtechnik, Postfach
3640,D-76021 Karlsruhe, Germany

**Abstract:**We present a dosing system, which consists of
four microvalves (presented by Rogge et al in the Proceedings of Eurosensors
XVI, Prague, 2002,pp 109–110) for controlling and a movable membrane for flow
measurement that divides a cavity into two chambers. The flow rate is determined
from the straining of the membrane caused by the entering fluid. The displaced
volume is detected by strain gauges integrated in the membrane. The overall
dimensions of the membrane and the entire system are 2 mm and 10 × 50 × 6
mm3, respectively. A simple control was coded for dosing a certain amount
of volume. This simple system has already achieved an accuracy of about 10%.
The dosing system is manufactured with the AMANDA process, which allows for
low-cost production of microcomponents from polymers.

⊙第62篇⊙

**Polymer
micro piezo valve with a small dead volume**

（下載英文論文全文請點擊上面的鏈接）

注意：本論文已在《INSTITUTE
OF PHYSICS PUBLISHING JOURNAL OF MICROMECHANICS AND MICROENGINEERING. 14 (2004)
305–309》發表

使用者請注明論文出處

Peige Shao1(邵培革), Zeno Rummler2 and Werner Karl Schomburg3

Forschungszentrum Karlsruhe, Institut f¨ur Mikrostrukturtechnik, Postfach
3640, D-76021,Karlsruhe, Germany

**Abstract:**A polymer valve with a small dead volume in
the range of 6 nl and a response time faster than 1 ms is presented. The valve
structure is simple and therefore easy to fabricate by injection molding or
hot embossing. A layer of silicone rubber applied by a stamping technique
not only promotes the sealing of the valve but also defines the gluing area
during assembly. The fabrication is based on the AMANDA-process, which allows
low-cost batch production of polymer micro devices.

⊙第63篇⊙

**溜冰機器人運動學分析**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《上海交通大學學報》2002,36
(9):1365－1369發表

使用者請注明論文出處

宋立博, 呂恬生, 張家梁, 費燕瓊

(上海交通大學機械工程學院，上海，200030)

**摘要：**依據Roller-walker和ALDURO重新設計了采用腿輪混合結構的溜冰機器人。在簡要介紹常規的運動學分析方法的基礎上，建立了相關的慣性坐標系和滾輪坐標系，并根據滾輪在法向無滑動、切向作純滾動的假設建立了中心定位輪的運動約束方程。然后，建立了機器人的運動學模型，并討論了機器人的移動性問題，得出機器人存在運動的條件。同時，設計了溜冰機器人運動學狀態空間表達式。最后，以溜冰機器人為例分析了其轉彎和直線滑行時的運動學問題。

**關鍵詞 ** 溜冰機器人，移動機器人，運動學，狀態空間

中圖分類號: TP242.1 文獻標識碼 A

**Kinematic Analysis of Ice-Skater Robot**

SONG Li-bo LÜ Tian-sheng ZHANG Jia-liang FEI Yan-qiong

(School of Mechanical Engineering of Shanghai Jiao Tong University，Shanghai，200030)

**ABSTRACT ** A Ice-skater Robot of leg-wheel type is redesigned
according to Roller-walker and ALDURO. On the basis of introduction of kinematic
analysis methods, the paper founds the stationary coordinate system and the
wheel coordinate system respectively. Meanwhile, the kinematic constraint
equations of the standard centered orientable wheel is founded on the assumption
that there is no slippage in normal direction and pure rolling in tangential
direction of the wheels. Then, the kinematic model is modeled and the mobility
is discussed in the paper. And the motion condition equation of the robot
is gotten in sequence. Meanwhile, the paper designs the kinematic state space
representation of the Ice-skater Robot. At last, the paper analyzes the kinematics
of the Ice-skater Robot when it turns and skates forwards respectively.

**KEYWORDS** Ice-skater Robot，Mobile robot,，Kinematics，State space

⊙第64篇⊙

**The
core doninance parameter of extragalactic radio sources**

（下載英文論文全文請點擊上面的鏈接）

注意：本論文已在《Asronomy
& Astrophysics June 11, 2003,1–14》發表

使用者請注明論文出處

J.H. Fan and J.S. Zhang

Certer for Astrophysics, Guangzhou University, Guangzhou, 510400, China

**Abstract: ** In this paper, based on a paper by Liu Zhang(2002),
we have chosen a sample of 542 extragalactic sources, for which we have calculated
the core-dominance parameters and investigated the relation between core-dominance
parameter and the core and extended luminosities. The core-dominance parameter
of galaxies is smaller than that in quasars, which is smaller than that in
BL Lac objects.

**Key words ** BL Lacertae objects; general, galaxies; quasars-galaxies;
Seyfert-galaxies; jet

⊙第65篇⊙

**基于小波變換和模糊算法的醫學圖像的邊緣檢測算法**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《大連理工大學學報》Vol.42,No.4.2002：504－508發表

使用者請注明論文出處

袁野1.2 歐宗瑛2

(1．大連理工大學自動化系，大連，116024 2．大連理工大學機械系CAD&CG研究所，大連，116024）

**摘要：**在醫學圖像三維顯示技術中，需要得到單象素級的清晰輪廓線。為了適應這種需求，本文提出了一種邊緣檢測算法，它基于Mallat小波模極大值邊緣檢測方法，同時應用模糊數學的原理為模極大值構造相應的隸屬函數，對得到的極大值進行進一步篩選，最終可以得到單象素級的邊緣。實驗結果證明了該算法的可行性。

**關鍵字：**小波變換，邊緣檢測，模極大值，隸屬函數，模糊算法

**A Method of Edge
Detection Based on Wavelet Transform and Fuzzy Algorithm**

Yuan Ye 1.2 Zhong Chongquan2
Ou Zongying 2

（1．Automation
Department, Dalian University of Technology, Dalian, 116024）

（2．CAD&CG
lab, Mechanical Engineering Department, Dalian University of Technology, Dalian,
116024）

**Abstract: ** In 3D render
technique of medical images, we need edges which are single pixel. In order
to meet this need, we proposed a method of edge detection, which based on
Mallat wavelet model maximum edge detection algorithm and fuzzy algorithm.
We designed a membership function for model maximum and pick suitable model
maximum , then the edge of single pixel can be detected. The experimental
results show that the algorithm is feasible.

**Keyword****s:**
wavelet transform, edge detection, model maximum, membership function, fuzzy
algorithm

⊙第66篇⊙

**應用神經網絡隱式視覺模型進行立體視覺的三維重建**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《計算機輔助設計與圖形學學報》,2003,15(3):293-296上發表

使用者請注明論文出處

袁野1.2 歐宗瑛2 田中旭3

(1． 大連理工大學自動化系，大連，116024) (2.大連理工大學機械學院CAD&CG研究所，大連，116024）

（3．上海大學機器人中心，上海，200072）

**摘要：**針對傳統的基于精確數學模型的立體視覺方法過程繁瑣的不足，本文提出了一種應用BP神經網絡隱式視覺模型進行三維重建的算法，將多個標定平面放置在有效視場內，用神經網絡模擬立體視覺由兩個二維圖像重建三維幾何的過程，經過網絡訓練建模后，無須攝像機標定即可進行三維重建。仿真實驗結果證明了該方法比較簡單，且能保持較高的精度。

**關鍵字：**BP網絡，立體視覺，三維重建

**3D Reconstruction
in Stereo Vision using Neural Networks implicit vision model**

Yuan Ye 1.2 Ou Zongying 2 Tian
Zhongxu3

（1．Automation
Department, Dalian University of Technology, Dalian, 116024）

（2．CAD&CG
lab, Mechanical Engineering Department, Dalian University of Technology, Dalian,
116024）(3.Robot Center ,Shanghai University
,Shanghai, 200072)

**Abstract: **
The classical stereo vision algorithms based on explicit model are very complicated,
an algorithm of stereo vision based on BP neural networks implicit vision
model was proposed in this paper. Multi calibration planes were placed in
the effective view field, neural network was used to approximate the process
from two image points to the 3D point, after training the BP networks a implicit
model was built, the 3D points can be reconstructed without the complicated
calibration. The experimental results show that the algorithm gains simplicity
and high accuracy.

**Keywords:** neural networks，stereo
vision，3D Reconstruction

⊙第67篇⊙

**三江平原毛果苔草濕地光輻射能的利用與分配**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《水生生物學報》2003，27（5）：502-506上發表

使用者請注明論文出處

何池全 李 蕾 顧 超 陸曉怡

（上海大學環境科學與工程系, 上海, 200072）

**摘要：**毛果苔草濕地的物理過程觀測設在中國科學院三江平原沼澤濕地生態實驗站內，用美國CID公司出品的光合儀對典型濕地中幾種優勢植物的光合能力進行測定；在80。C干燥的植物樣品（含各種不同的構件），粉碎后，分別稱量約1g左右，用美國公司Parr型氧彈式熱量計測定；研究發現毛果苔草濕地建群種中毛果苔草的凈光合速率最大,
為47.41μmol·m-2·s-1。以太陽總輻射能和生長季內光合有效輻射為基礎計算出各器官的能量利用效率計, 極大值是細根, 分別為1.3945%和3.1879%,
極小值是穗, 分別為0.0020%和0.0046%，毛果苔草種群的能量利用率為2.54%。濕地不同植物群落地下部分的能量含量分布中毛果苔草群落的地下部分能量含量的平均值最大。這說明毛果苔草種群具有較高的能量轉化效率，并將大部分能量儲存在地下部分。在不同層次的能量含量分配中，隨著土壤深度的增加，地下部分的能量含量是趨于遞減趨勢的。

**關鍵詞：**毛果苔草；濕地生態系統；光合作用；初級生產效率；地下器官能量含量

**The utilization and distribution of the
sunshine radiant energy of Carex lasiocarpa wetland in Sanjiang Plain**

He Chiquan Li Lei Gu Chao Lu Xiaoyi

(Department of Environmental Science and Engineering, Shanghai University;Shanghai,200072)

**Abstract: ** Carex lasiocarpa is a rhizomatous clonal species
of mire wetlands in Northeastern of China. The fieldwork about physical process
of Carex lasiocarpa wetlands was carried out in the Shangjiang Plain Mire
Wetlands Ecological Experiment Station in Chinese Academy of Science in Northeastern
of China (47。31`N, 133。31`E). The field work was carried out in a typical
Carex lasiocarpa wetlands, which areas is 200×450m2 and it can divided into
three areola, namely the determined areola of biomass; the determined areola
of wither biomass and its decompose areola, and then it was setup each other
which was used to sampling and observation from May to October in 1998-1999，the
frequency was about 30d, the sampling area was 1×1 m2 with 2~3 times. The
plants were divided into different compartments, in which is leaf, sheath,
rhizome, inflorescence, spike, radicula and dead standing sampling, and dried
to constand weight at 80。C, after which they were ground and samples were
taken for analysis. The plant caloric value is determined by Parr type Oxygen
bomb heat meter which is made in America. The photosynthesis is determined
by photosynthesis meter, which is made in CID company in America; is analys
Plant photosynthesis is the original force to impel and to support the whole
ecosystem, we found that the net photosynthesis rate of Carex lasiocarpa is
biggest than others in Carex lasiocarpa wetland, which is 47.41μmol·m-2·s-1.
In the basis of the overall sunshine radiation and the photosynthesis availability
radiation to count the energy utilization rate of each organs/component, the
maximum is radicula, which are 1.3945% and 3.1879%, the minimal value is spike,
which are 0.0020% and 0.0046%，the energy utilization efficiency of Carex lasiocarpa
population is 2.54%. The average value of underground organs/components energy
content of Carex lasiocarpa community is biggest than its in others community,
which showed that C. lasiocarpa had higher energy productive efficiency and
most energy was stored in their under-ground part, the reason for these were
also discussed. In the allocation of energy content in different underground
layer, with the increase of soil depth, energy content in different underground
layer is decrease by degrees.

**Keywords:** Carex lasiocarpa, wetland ecosystem, photosynthesis, primary
production efficiency, energy content

⊙第68篇⊙

**THE
ALLELOPATHIC EFFECT OF Acorus tatarinowii UPON ALGAE**

（下載英語論文全文請點擊上面的鏈接）

注意：本論文已在*Journal of Environmental Science.* 2001, 13(4):481-484上發表

使用者請注明論文出處

Chiquan He(何池全)

The department of Environmental Science & Engineering, Shanghai University;
Shanghai 200072, China

Changke Wang（王長科）

Changchun Institute of Geography, Chinese Academy of Sciences，Changchun, 130021，China)1

**Abstract: ** Besides competing with algae for light and
mineral nutrients (i.e. N, P, etc.), the root system of Acorus tatarinowii
excretes some chemical substances, which injure and eliminate alga cells,
to inhibit the growth of the algae. When the algae cells were treated in "A.
tatarinowii water", some of the chlorophyll a were destroyed and the photosynthetic
rate of algae decreased markedly and the ability of alga cells to deoxidize
triphenyltetrazolium chloride (TTC) reduced greatly. Then alga cells turned
from bright red to bluish green under fluorescence microscope. These showed
that the allelopathic effects of A. tatarinowii on algae were obvious and
planting A. tatarinowii can control some green algae. The experiment on the
extractions of the secretions of the root system showed that the inhibitory
effect had a concentration effect. If the concentration of the root secretion
was below 30ul/disc, the inhibitory rate was negative; if it was over 45ul/disc,
the inhibitory rate was positive. This proved that the influence of the root
secretion on the same acceptor was a kind of concentration effect. When the
concentration of the root secretion was low, it promoted the growth of algae;
when the concentration reached a definite threshold value, it restrained the
growth of algae. In present case, the threshold value was between 30 ul/disc
and 45 ul/disc.

**Keywords:** Acorus tatarinowii Allelopathy Algae Wetlands

第69篇⊙

**鋼筋混凝土柱“強剪弱彎”設計可靠性分析**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《水利學報》 2002(4):88-92,96上發表

使用者請注明論文出處

馬宏旺

（大連理工大學海岸及近海工程國家重點實驗室，遼寧 大連 116024）

**摘要：**基于現行建筑抗震設計規范（GBJ11-89），把鋼筋混凝土柱的設計參數看作隨機變量，柱的破壞看作由抗彎與抗剪失效模式組成的串聯體系，采用Monte
Carlo模擬法，分析了鋼筋混凝土柱“強剪弱彎”設計的可靠性。重點分析了不同軸壓比下，鋼筋混凝土框架柱剪切破壞先于彎曲破壞發生的概率，為合理的確定剪切增強系數提供分析參考。

關鍵詞：鋼筋混凝土柱 強剪弱彎 可靠性分析 Monte Carlo模擬

**Reliability Analysis for Strong
Shear-Weak Bending Design of Reinforced Concrete Columns**

Reliability Analysis for Strong
Shear-Weak Bending Design of Reinforced Concrete Columns

Ma Hongwang

(Civil Engineering, Dalian University of Technology,116023)

**Abstract: ** Based on current
seismic design code, design parameters of reinforced concrete columns are
considered as random variables. Failure mode of columns is considered as series
system. Reliability of Strong shear-weak bending design is analyzed by Monte
Carlo simulation method. The probability of shear failure prior to flexural
failure is obtained, Aiming to provided to reference for determining shear
strength factor.

**Keywords:** reinforced concrete column Strong shear-Weak bending reliability
analysis Monte Carlo simulation

第70篇⊙

**鋼筋混凝土框架梁基于可靠度理論的抗震優化設計**

（下載論文全文請點擊上面的鏈接）

注意：本論文已在《建筑結構》 2003，9上發表

使用者請注明論文出處

馬宏旺 呂西林

（同濟大學土木學院結構工程與防災研究所，200092，上海）

**摘要：**針對混凝土設計規范（GB 50010-2002）中，矩形、T形和I形截面的一般框架梁抗剪設計進行可靠度評估。把梁的設計參數（混凝土強度、箍筋配筋率、鋼筋強度、自重荷載效應和地震作用效應）看作隨機變量，采用Monte
Carlo 模擬法，得出按新規范設計不同抗震等級梁的抗剪可靠指標的變化范圍。把設計參數分別看作確定性變量和隨機變量，文中針對新、舊規范（GBJ10-89）的抗剪設計安全性進行了比較分析。結果表明按照新規范進行梁的抗剪設計比舊規范更安全。

**關鍵詞：**鋼筋混凝土梁 抗剪 可靠度 Monte Carlo模擬

**Reliability Evaluation of
Seismic Shear Design for Reinforced Concrete Beams**

Ma Hongwang , Lu Xilin

(Civil Engineering Department of Tongji University, ShangHai 200092,China)

**Abstract:** Reliability evaluation
for seismic shear design of general reinforced concrete frame beams designed
following The Code(GB 50010-2002)is finished. The design parameters such as
strength of concrete, strength of steel, gravity load and earthquake action
are regarded as random variables. Seismic shear reliability index of the beams
is obtained by Monte Carlo simulation method. At the same time, from two aspects
of determination and uncertainty, safety of seismic shear design of beams
is compared between the new code(GB50010-2002) and the old code(GBJ10-89).
The results indicated that shear design of beams following the new code is
more safety than following the old code.

**Key words:** reinforced concrete beam; shear design; reliability

第一頁 第二頁 第三頁 第四頁 第五頁 第六頁 第七頁 第八頁 第九頁 第十頁 第11頁

返回首頁 | CIMS論文 | 并行工程 | 虛擬制造 | 敏捷制造 | 其他論文 | 項目開發 | 學術資源 | 站內全文搜索 | 免費論文網站大全 |

為了更好的為大家服務，歡迎您參加本站的投票調查

本站永久域名：http://www.sqvswk.live歡迎訪問

注意：本站內容未經書面允許不得轉載

All
rights reserved, all contents copyright 2000-2019

本站自2000年3月總網頁訪問量為

pk10开奖记录直播
本站自2000年3月總網頁訪問量為